company profile
Shanghai Uzong Industrial Co., Ltd. (hereinafter referred to as UZONGLAB®) is a high-tech company that provides integrated solutions for intelligent laboratories, mainly serving the Chinese market and countries along the “Belt and Road”. It has three business divisions and one The technology center, namely the instrument business department, consumables business department, project development department, and Zhongyu Lianhe Technology Center. In addition to the Shanghai headquarters, we have established branches in Beijing, Shenyang, Shijiazhuang, Taiyuan, Qingdao, Guangzhou, Chengdu and Urumqi. To provide customers with more professional, safer and more convenient products and services is our sole goal. Cornerstone氫氧氮分析軟件同時支持***的書記文檔格式和可變的報告格式。專業元素分析儀采購
Procedure – Powder/Chip Samples
Determine the instrument blank.
Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.
Clean the upper and lower electrode either manually or remove the crucible and press the analyze button to clean with an automatic cleaner if applicable.
Add approximately 0.05 g of *** Graphite Powder to a 782-720 Graphite Crucible.
Firmly place the crucible on the lower electrode tip or appropriate autoloader position.
力可ONH836氧氮氫分析儀
特點和優勢
國際**的非色散紅外及熱導檢測器 ,無移動部件,不需要手動調整
采用三個**的紅外器檢測氧含量,同時檢測CO和CO2,然后在轉化為CO2集中檢測,原理上是**完善的,所以不僅可以保證中間量程的測量精度,在**含量和高含量的檢測范圍內同樣可以滿足精度要求
高性能的紅外檢測器配置***恒溫絕熱技術,消除了外界環境溫度的干擾
長壽命的紅外發射光源和無漂移的電路設計保證檢測器的長期穩定性
力可**的動態流量補償控制DFC系統,保證了流量系統的完善,可以精確控制整個氣路中的流量,保持流量恒定**改善了材料中氮分析的準確度
可以旁路的OMI-2 氣路強化過濾裝置增強了檢測器的穩定性,使得分析結果更加準確
可選自動功能
20位試樣自動進樣系統
通用下電極坩堝支座,容納各種坩堝使用
無需人工干預的全自動清掃系統
Summary
The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high
mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power
electrode furnace to quickly and efficiently release the target gases from within the sample, which allows
for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.
提供各種無機材料、鋼鐵、有色金屬、硬質合金、陶瓷材料中寬范圍的氧氮氫同時分析。
氧氮氫分析儀的使用注意事項:
1 、氧氮氫分析儀在初次啟用前,應該對連接點、焊點、閥門等進行檢漏,以確保空氣中的氧不會反滲進入管道及儀器內部,造成測量數值偏高。
2、再次使用儀器前,要進行管道系統凈化,將漏入的空氣除干凈,同時確保連接取樣管路時沒有漏入空氣。
3、樣氣中氧含量的變化會受管道材質及表面粗糙度影響,因此一般連接管路選用銅管或拋光過的不銹鋼管,而不用塑料管、橡膠管等。
4、微量元素分析時,要避免各種管件、閥門、表頭等死角對樣氣造成污染,因此必須盡可能的簡化氣路系統,連接件死角要小,以防止溶解氧逸出造成污染,使用水封、油封及臘封等設備,才能較好的確保數據的。
***紅外池的恒溫絕熱技術消除了外界環境溫度的干擾。廣東進口分析儀采購
***電極爐頭設計,提高脈沖爐熱交換效率。專業元素分析儀采購
Determine the instrument blank.
a. Login a minimum of 3 Blank replicates.
b. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.
c. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.
d. Clean the upper and lower electrode manually, or, if applicable, remove thecrucible and press the analyze button to clean with the automatic cleaner.
e. Firmly place a graphite crucible on the lower electrode tip.
f. Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and endautomatically.
g. Repeat steps 2b through 2f a minimum of three times.
h. Set the blank following the procedure outlined in the operator's instruction manual.
專業元素分析儀采購